It is a cement-based, single-component, polymer-modified, flexible, high-performance and
stable powder adhesive mortar with reduced
slip properties (C2T).
It is flexible and provides strong adhesion. It is resistant to water and
frost, and is unaffected by temperature changes. It offers high stability
and does not sag in vertical applications. Allows tiling from top to bottom.
| Appearance | Powder |
|---|---|
| Color | Grey and White |
| Packaging | 25 kg Kraft Bag |
| Standard | EN 12004-1 |
| Poz No. | 10.300.2202 |
| Class | C1T |
| Quantity per Pallet | 60 Kraft Bags, 1500 k |
| Mixing Ratio | % 22 - 24 |
|---|---|
| Waiting Time | 5 minutes |
| Adjustment Time | ≤ 20 minutes |
| Pot Life | ~3 hours |
| Open Time | ≥ 30 minutes |
| Consumption (kg/m²) | 4,0 – 6,0 |
| Initial Adhesion Strength | ≥ 0,50 N/mm2 |
|---|---|
| After Water Immersion | ≥ 0,50 N/mm2 |
| After Heat Aging | ≥ 0,50 N/mm2 |
| After Freeze-Thaw Cycles | ≥ 0,50 N/mm² |
| Adhesion Strength Open Time | ≥ 0,50 N/mm² |
| Slip | ≤ 0,50 mm |
| Reaction to Fire Class | A1 |
In interior and exterior areas, On horizontal and vertical surfaces, For the installation of large-sized floor and wall ceramics, granite, porcelain tiles, marble, clinker, and all types of natural stone cladding materials, In areas exposed to heavy pedestrian traffic such as workplaces, shopping malls, schools, and hospitals, Used for tiling over existing granite and marble surfaces.
25 kg Kraft Must be stored in its unopened original packaging, in a cool and dry environment, protected from frost. The appropriate storage temperature should be between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions.
During mixing and application, contact of the material with skin and eyes should be avoided. In case of contact, rinse thoroughly with plenty of water. If eye contact occurs, rinse immediately with plenty of water and seek medical advice. Protective gloves, clothing, mask, and goggles should be worn during use.
Approximately 5.50 – 6.00 liters of clean water should be poured into a container, and 25 kg of SY 550G should be added slowly. It should be mixed using a low-speed mixer or a trowel until a homogeneous mixture is obtained. No substances other than those specified in the application instructions should be added to the mixture. The prepared mortar should be left to rest for 3 – 5 minutes to mature, then mixed again for 1 – 2 minutes before application. The mortar should be applied to the surface, and its thickness adjusted using a notched steel trowel. The size of the trowel teeth should be selected based on the size of the tiles and the flatness of the surface. For interior applications with tiles larger than 1100 cm², adhesive should be applied both to the surface and the back of the tile (double-sided bonding). To ensure good adhesion, pressure should be applied using a rubber mallet to expel air. The combed mortar must be tiled within a maximum of 15–20 minutes. If this time is exceeded, no tiling should be done, and the mortar should be scraped off the surface. The prepared mortar must be used within 3 hours. The product must be used within its pot life. Any mortar that has exceeded its usage time or formed a crust in the container must not be used. Tiles adhered with SY 550G should not come into direct contact with water for at least 24 hours. Protect from freezing and strong sunlight for 5–7 days. Grouting should be done at least 24 hours after floor tiling applications. Floors can be opened to light foot traffic 24 hours after application. During and after application, the surface should be protected from drafts. The mixture should be prepared using water at room temperature. Do not apply during rainy weather.