Cement-acrylic based, fully flexible waterproofing material.
It is a cement and acrylic-based, two-component, fully flexible, capillary-effective
waterproofing mortar that can be applied on both positive and
negative sides
Genel Özellikleri
NANOSER NANO FX 100 is a cement and acrylic-based, twocomponent, fully flexible
waterproofing material applied to concrete
surfaces from the inside or outside (negative-positive) to protect against
leaks and surface water.
| Görünüm | Gri Toz, Beyaz Sıvı |
|---|---|
| Standardı | TS EN 1504-2 |
| Sınıfı | Pr. 2,2 ve 8,2 |
| Palet Miktarı | 60 Kraft, 60 Bidon |
| Karışım Oranı | A/B: 25/10 |
| Kat Sayısı | 2-3 |
| Uygulama Kalınlığı | 2-4 mm |
| Bekleme Süresi | 5-6 Saat |
| İşlenebilme Süresi | (+25°C) ~ 45 dakika |
| Ral Renkleri | Gri – Beyaz |
| Kap Ömrü | ~3 saat |
|---|---|
| Yapışma Dayanımı | (N/mm²) ≥ 1,50 |
| Çekme Dayanımı | (N/mm²) ≥ 3,50 |
| Negatif Su Basıncı Direnci | 4 bar |
| Pozitif Su Basıncı Direnci | 10 bar |
| Kapiler Su Emme | (kg.m-2.dk-0,5) ≤ 0,10 |
| Yangına Tepki Sınıfı | Bs1d0 |
| Kuru Film Ağırlığı | 125 - 250 Mikron |
| Yapışma Dayanımı | (Beton&Çelik) (7 gün) >2,50 N/mm2 |
| Kürlenme Süreleri | (+35°C) İlk Kürü-12 saat Son Kürü-7 gün |
It is used in both interior and exterior applications, on vertical and horizontal surfaces, terraces (with protection over gray-colored applications), and in areas exposed to UV light, where white color should be used. It is also suitable for textile industry soft water (pH between 3 and pH 7) storage pools, water tanks, and Olympic swimming pools, elevator pits, wet areas such as WC, bathrooms, kitchens, and balconies, as part of a foundation waterproofing system, in areas sensitive to movement, vibration, and slight settling, to protect concrete from water, carbonation, and de-icing salts. Additionally, it is used in facilities like spas and Turkish baths.
Packaging: A: 25 kg Kraft B: 10 kg Canister Color: Gray It should be stored in a clean, dry, and moisture-free environment, between +5°C and +35°C, protected from direct sunlight. It must be shielded from water, frost, and harsh weather conditions. It can be stacked up to 10 layers high. If the specified storage conditions are followed, the shelf life is up to 12 months from the production date.
During application and mixing, contact with skin and eyes should be prevented. In case of contact, wash immediately with plenty of water. If contact occurs with the eyes, rinse immediately with plenty of water and seek medical assistance. Protective gloves, clothing, mask, and goggles should be worn during use.
The surface must be clean, damp, smooth, and solid. Significant defects and holes on the surface should be repaired with NANOREP FT – 70 / 30 series repair mortars at least 24 hours before applying NANOSER NANO FX100. To ensure the continuity of the waterproofing, vertical and horizontal corners should be beveled. Surfaces like raw concrete or cement-based plaster should be wetted with clean water, and the surface should be kept damp until the water layer disappears. The B component of NANOSER NANO FX 100 should be gradually added to the A component, and mixed with a low-speed mixer for about 2-3 minutes until a homogeneous consistency is achieved. After letting the mixture rest for 2 minutes, it should be mixed again for 30 seconds to make it ready for application. NANOSER NANO FX 100 should be applied in at least 2 coats using a brush or spray method. If using a brush, each coat should be applied in a direction perpendicular to the previous one. Reinforcement mesh should be applied immediately after the first coat. There should be at least 5 hours of waiting time between coats. The application rates are approximately 1.45 kg/m² for the first coat, 1.30 kg/m² for the second coat, and 1.15 kg/m² for the third coat. The optimum wet film thickness for each coat should be around 1.3 mm. The prepared mortar should be used within 2 hours.